How to recover broken drill machine

In this project we learn how to recover broken drill machine easy at home. our old drill machine casing broken form hand side. we cannot use this casing. so we make new casing with the help of PVC pipe.

for making this project we need some components.

2 inch PVC Tee
2 inch PVC Pipe round about 1 foot
2 inch PVC cap
drill machine switch
laptop battery cell
BMS 12V 20amp or 10amp
Machine oil
Grease
kerosene oil

1st open all screw. if screw hard then apply some WD-40 spray.

Now remove all gears form drill machine.

And now take kerosene oil and clean all parts with the help of brush.

Now dry all parts with the help of cloth.

And now apply some machine oil and grease on all gears.

Now close all parts and apply machine oil and grease time to time.

after successfully close drill machine take 2 inch T and adjust this drill machine on it.

now take laptop battery and make 12v power.

And now connect BMS for over charge protection. Using this image you can easily connect battery cell with BMS.

And finally make a design as your demand with the help of paint.

for more batter under stand you can watch this video.

Video of recover old broken drill machine:

Total cost of recover broken drill machine project:

The total cost of this project is round about 3.7$
PVC T price is roundabout 0.5$
PVC cap price is round about 0.4$
PVC pipe price is round about 0.2$
Drill machine switch price is round about 0.6$
BMS price is round about 1$
Old laptop battery price is round about 1$

how to make 12v stand fan

How to make 12v stand fan

In this project we learn how to make 12v stand fan easy at home. Its very easy, useful, low cost, and energy saving project. in this project we use PVC Pipe and 12v DC fan motor. other all components detail are following.

Components:

12V DC Long shaft Motor
2 inch PVC Tee
2 inch PVC Cup
3, or 4 inch round PVC Piece.(its depend on your fan jali inner hole.
12v 2amp or 4 amp charger
2inch 3 foot PVC Pipe
Fan wing ( 14 inch)
Fan Base ( you can make it with sand and cement)
Fan Grill or Jali (14 inch wing jali)

if you want to make small fan then you can chose small fan grill and fan wing. i want 14 inch stand fan so i use 14 inch wing and grill.

now following simple steps and make same.

Adjust DC fan motor on 2 inch PVC cup with the help of screw.
Also connect 4 inch round PVC piece.
Now connect back side of fan grill with dc fan motor set.
connect fan wing after connect back side of fan grill.
and now connect front side of fan grill with back side of fan grill.
now take a 3 inch long PVC pipe and connect with PVC cup and PVC tee.
Take fan base and connect 3 foot PVC pipe and make fan stand.
now connect tee with stand
and finally connect wire connection with dc motor and 12v charger.

Video of homemade 12v dc stand fan

Total cost for making 12V DC stand fan:

Total cost for making 12v dc stand fan is round about 7.25$. all components price are following

New 12V DC Motor = 3.12$ in local market ( you can buy it more cheapest price from scrap shop.
New 14 inch fan wing = 1$
used fan grill = 1.3$ (new fan grill or jali price is 2.5$)
2 inch PVC Tee = 0.63$
2 inch PVC Cup = 0.32$
2 inch 3 foot PVC Pipe = 0.25$/foot
cement = 0.13$/kg
sand = free

How to make powerful rechargeable drill machine using pvc pipe

In this project we learn how to make powerful rechargeable drill machine using pvc pipe easy at home. Here we use BMS charging module. its use for battery over charge protection. and we can charge batteries with any 12v charger. for making this project we need some components.

components:

12v gear motor or old drill motor (you can get it form old scratch shop)
1.5 inch Tee or 1.75 inch Tee
1.5 inch or 1.75inch half foot length PVC Pipe (PVC size must match with Tee, if you chose 1.5 inch tee then PVC size also has 1.5 inch)
12v BMS Charging module (its protect our batteries to over charge and increase batteries life)
Push switch or on/off switch
female connector (its use for connect 12v charger)
Lethem batteries ( i use 6 batteries for good backup, you can use 3 batteries)
Plastic box
Soldering wire
Soldering iron

PVC pipe and Tee are total depend on Gear motor. so 1st try to buy gear motor and then buy PVC pipe and tee as per gear motor size. I find old drill motor its fit on 1.5 inch to 1.75 inch PVC Tee.

Now following these simple steps and make.

1st Connect 2 wires with push button and then fit it on half foot PVC pipe.
2nd adjust this PVC pipe on plastic box cap you can use power glue for fixing.
Now connect 2 wires with motor and adjust this drill motor on PVC Tee.
And now adjust this PVC on Tee.
Now take 6 Lethem batteries and make a 3 pear in parallel connection. you can use 3 batteries. i use 6 because i want good backup power.
And now connect all pears in series and make 12v output cell.
Now connect BMS circuit with batteries for over charge protection.
BMS input charging wires connect with female connector.
And finally adjust all cell and circuit on plastic box.

Video of homemade rechargeable drill machine:

Total cost of rechargeable drill machine project:

the total cost of rechargeable drill machine is round about 8$. other all components price are following.

Drill motor = 3.5$ (you can buy it more cheaper price from old scratch shop)
12v BMS 3S charging module = 2.25$ ( if you use laptop battery circuit then you can save this amount)
1.5 inch PVC Tee = 0.65$
1.5 inch PVC Pipe = 0.2$/foot
Push button = 0.13$
female connector = 0.13$
old laptop battery = 1$

how to make beautiful table using pvc pipe

In this project we learn how to make beautiful table using pvc pipe easy at home. its very cheapest useful project. I use 2 inch pvc. you can chose as your demand and as your wish. for making this project we need some components.

Components:

Tee 4
Elbow 4
15 inch PVC 6
39 inch PVC 2
Hard board 4/2 feet
Suction Cup 4

Now follow this simple steps and make same.

take 15 inch PVC and connect Tee on both side. and make 2 set.
Now take other 4 15 inch PVC and connect elbow on 1 side.
and 2nd side connect with tee.
now both 39 inch PVC connect with 2nd side of elbow.
and finally adjust hard board on this frame.

you can adjust hardboard with the help of suction cup. its very easy to fit. if you don't like suction cup then you can use 3 inch nut bolt.

video of homemade pvc pipe study table:

we can use it as a pvc pipe study table. and also use it as a computer table. its total depend on you.

Total cost of this project:

In this table i use 2 inch pvc pipe and total cost of this project roundabout 16$ in my area. other all components price are following.

Tee price = 0.65$/piece
Elbow price = 0.55$/piece
PVC pipe = 0.26$/foot
Hardboard 4/2 foot = 3.5$
Suction Cup = 0.05$/piece

Easy Creative Projects

Labels

Technology

Breaking News

How to recover broken drill machine

How to recover broken drill machine

Video of recover old broken drill machine:

Total cost of recover broken drill machine project:

how to make 12v stand fan

How to make 12v stand fan

Video of homemade 12v dc stand fan

Total cost for making 12V DC stand fan:

How to make powerful rechargeable drill machine using pvc pipe

How to make powerful rechargeable drill machine using pvc pipe

Video of homemade rechargeable drill machine:

Total cost of rechargeable drill machine project:

how to make beautiful table using pvc pipe

how to make beautiful table using pvc pipe

video of homemade pvc pipe study table:

Total cost of this project:

Easy Creative Projects

Contact Form